Search Results for ipv6 to 4 tunnel ubnt

自建 6in4 Tunnel Server (iproute2)

IPv4下连IPv6有无数种解决方案，传统的6to4, 6in4, TEREDO…没兴趣讲优缺点，可以在wikipedia的页面上看看各家都用了啥。 TunnelBroker.net 应该是没IPv6的地方最流行的上IPv6的解决方案了。如果你觉得它不爽，其实自己搞一个也没那么难。上边wikipedia页面里说HE的技术实现是Unknown。其实自己试过一次大概都能知道应该往哪个方向去研究它的技术实现了。贴一个我路由器上的IPv6 Tunnel信息。

tun0      Link encap:IPv6-in-IPv4  
          inet6 addr: fe80::c0a8:b01/64 Scope:Link
          inet6 addr: 2001:470:23:1xx::2/64 Scope:Global
          UP POINTOPOINT RUNNING NOARP  MTU:1480  Metric:1
          RX packets:900942 errors:0 dropped:0 overruns:0 frame:0
          TX packets:905985 errors:4 dropped:0 overruns:0 carrier:4
          collisions:0 txqueuelen:0 
          RX bytes:559785922 (533.8 MiB)  TX bytes:179756964 (171.4 MiB)

tun0 Link encap:IPv6-in-IPv4

inet6 addr: fe80::c0a8:b01/64 Scope:Link

inet6 addr: 2001:470:23:1xx::2/64 Scope:Global

UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1

RX packets:900942 errors:0 dropped:0 overruns:0 frame:0

TX packets:905985 errors:4 dropped:0 overruns:0 carrier:4

collisions:0 txqueuelen:0

RX bytes:559785922 (533.8 MiB) TX bytes:179756964 (171.4 MiB)

首先，UBNT给我创建的interface是tun0；其次 Link encapsulation 是 IPv6-in-IPv4，也就是传说中的 6in4；再往下看，POINTOPOINT。再加上TunnelBroker的Example Configurations里给了一个iproute2的配置方法：

modprobe ipv6
ip tunnel add he-ipv6 mode sit remote 74.82.46.6 local xx.xx.xx.xx ttl 255
ip link set he-ipv6 up
ip addr add 2001:470:23:1xx::2/64 dev he-ipv6
ip route add ::/0 dev he-ipv6
ip -f inet6 addr

modprobe ipv6

ip tunnel add he-ipv6 mode sit remote 74.82.46.6 local xx.xx.xx.xx ttl 255

ip link set he-ipv6 up

ip addr add 2001:470:23:1xx::2/64 dev he-ipv6

ip route add ::/0 dev he-ipv6

ip -f inet6 addr

思路很简单了。假设服务器端为S，用户路由为R，则两边的参数逻辑应该是： S: Remote: R.ipv4 Local: S.ipv4 V6 IP: S.ipv6 Route: v6子网/CIDR R: Remote: S.ipv4 Local: R.ipv4 V6 IP: R.ipv6 Route: ::/0 即默认路由具体来说，假设你S的IP为1.1.1.1，可支配的IPv6 pool为 2400:1234:5678:9abc::/64，R的IP为2.2.2.2，上述的配置可能是： S.ipv4 = 1.1.1.1 S.ipv6 = 2400:1234:5678:9abc:1000::1/80 v6子网/CIDR = 2400:1234:5678:9abc:2000::/80 R.ipv4 … Continue reading “自建 6in4 Tunnel Server (iproute2)”

抛开路由为局域网内机器启用IPv6

支持IPv6这事情不一定非得要路由上配，局域网内只要有Linux机器能用IPv6就行。这种事情做之前，对于完全不会的人和会的人都很简单，但对我这种稍微懂一点的，还没做可能就先想多了。测试环境公司路由：TP-Link某老旧企业路由，不支持IPv6 Linux：Debian Jessie, 服务主机，兼顾dns，dhcp等等服务，LAN接口eth0 网络：北京联通家庭光纤 PPPoE IPv6 服务：Tunnel Broker 其他软件：dnsmasq, dhcpd Incoming search terms:北京联通 ipv6维盟 ipv6blueuk3free ddnsipv6 局域网linux v4tunnelstoodwx7tp-link不支持ipv6tunnel brokerubnt ipv6北京联通 pppoe ipv6维盟路由启用ipv6维盟路由器 ipv6Link to this post!

TunnelBroker for EdgeRouter Lite

创建隧道在北京联通这种不给IPv6网络的ISP下生存，总有走v6翻墙的欲望。免费的Tunnel服务很多，最出名莫过HE.net的TunnelBroker 首先申请一个Tunnel。访问：

https://tunnelbroker.net/new_tunnel.php

1	https://tunnelbroker.net/new_tunnel.php

注册登录之后，创建并输入当前路由公网IP “YOUR.ROUTER.INTERNET.IP”。创建成功后会被跳转到

https://tunnelbroker.net/tunnel_detail.php?tid=XXXXX

1	https://tunnelbroker.net/tunnel_detail.php?tid=XXXXX

XXXXX的部分是一串数字，所谓的Tunnel ID. 在这个页面上选择第二个标签页 “Example Configurations” 选择 “Vyatta / Ubiquiti EdgeMAX” 文本框会自动生成如下配置：

configure
edit interfaces tunnel tun0
set encapsulation sit
set local-ip YOUR.ROUTER.INTERNET.IP
set remote-ip 74.82.46.6
set address 2001:470:23:XXXX::XX/64
set description "HE.NET IPv6 Tunnel"
exit
set protocols static interface-route6 ::/0 next-hop-interface tun0
commit

configure

edit interfaces tunnel tun0

set encapsulation sit

set local-ip YOUR.ROUTER.INTERNET.IP

set remote-ip 74.82.46.6

set address 2001:470:23:XXXX::XX/64

set description "HE.NET IPv6 Tunnel"

exit

set protocols static interface-route6 ::/0 next-hop-interface tun0

commit

remote-ip是创建时选择的远端服务器IP，local-ip是本地当前的出口IP。鉴于ISP给的IP都是动态的，所以local-ip改成如下‘0.0.0.0’。如果之前有配置过tunnel，需要重新配置，则先删除既有的：

delete interfaces tunnel tun0

1	delete interfaces tunnel tun0

下面开始命令配置tunnel

configure
# tun to ipv6
edit interfaces tunnel tun0
set encapsulation sit
set local-ip 0.0.0.0
set remote-ip 74.82.46.6
set address 2001:470:23:XXXX::XX/64
set description "HE.NET IPv6 Tunnel"
exit
set protocols static interface-route6 ::/0 next-hop-interface tun0
commit
save

configure

# tun to ipv6

edit interfaces tunnel tun0

set encapsulation sit

set local-ip 0.0.0.0

set remote-ip 74.82.46.6

set address 2001:470:23:XXXX::XX/64

set description "HE.NET IPv6 Tunnel"

exit

set protocols static interface-route6 ::/0 next-hop-interface tun0

commit

save

Router Advert 配置完tunnel，就得配局域网内的配置了，毕竟只有路由能上v6是不够的

interfaces {
    ethernet eth0 {               
        address 192.168.11.1/24   
        duplex auto               
        ipv6 {                    
            address {             
                autoconf           
            }                     
            dup-addr-detect-transmits 1
            router-advert {                        
                cur-hop-limit 64  
                link-mtu 0        
                managed-flag false
                max-interval 600  
                other-config-flag false
                prefix 2001:470:24:xxx::/64 {
                    autonomous-flag true
                    on-link-flag true       
                    valid-lifetime 2592000         
                }                 
                radvd-options "RDNSS 2001:470:20::2  {} ;"
                reachable-time 0  
                retrans-timer 0   
                send-advert true  
            }                     
        }                         
        speed auto                          
    } 
...
}

interfaces {

ethernet eth0 {

address 192.168.11.1/24

duplex auto

ipv6 {

address {

autoconf

}

dup-addr-detect-transmits 1

router-advert {

cur-hop-limit 64

link-mtu 0

managed-flag false

max-interval 600

other-config-flag false

prefix 2001:470:24:xxx::/64 {

autonomous-flag true

on-link-flag true

valid-lifetime 2592000

}

radvd-options "RDNSS 2001:470:20::2 {} ;"

reachable-time 0

retrans-timer 0

send-advert true

}

speed auto

}

...

}

如果你本地的DNS规则有过配置，radvd-options 的配置一定要把ipv6地址设成路由器的v6地址实践证明，我之前折腾了好久的dhcpv6没用，但是配置也可以贴出来

...
service { 
...                     
    dhcpv6-server {                              
        shared-network-name LAN_DEAD {   
            name-server 2001:4860:4860::8888
            name-server 2001:4860:4860::8844 
            subnet 2001:470:23:xxxx:dead::/80 {   
                address-range {         
                    start 2001:470:23:xxxx:dead::1000 {
                        stop 2001:470:23:xxxx:dead::8000
                    }                            
                }                       
                name-server 2001:4860:4860::8888 
                name-server 2001:4860:4860::8844
                prefix-delegation {              
                    start 2001:470:23:xxxx:dead::1000 {
                        prefix-length 80
                    }                  
                }                          
            }                           
        }                               
    }  
}

...

service {

...

dhcpv6-server {

shared-network-name LAN_DEAD {

name-server 2001:4860:4860::8888

name-server 2001:4860:4860::8844

subnet 2001:470:23:xxxx:dead::/80 {

address-range {

start 2001:470:23:xxxx:dead::1000 {

stop 2001:470:23:xxxx:dead::8000

}

name-server 2001:4860:4860::8888

name-server 2001:4860:4860::8844

prefix-delegation {

start 2001:470:23:xxxx:dead::1000 {

prefix-length 80

}

自动更新IP 之前一片EdgeRouter Lite相关的配置文章里，我把He.net提供的DDNS配置好了。Dynamic DNS on HE.net, HE.net Dynamic DNS on Ubiquiti Router. 脚本更新首先按如下路径生成ddns专用的key

TunnelBroker.net -> Tunnel Details -> Advanced -> Update Key

1	TunnelBroker.net -> Tunnel Details -> Advanced -> Update Key

尝试过好多次，EdgeRouter Lite无法通过配置参数添加多个同类型的ddns配置。所以先提供一个简单粗暴的方法。参考 https://forums.he.net/index.php?topic=1994.0 的说明，有如下的客户端语法： … Continue reading “TunnelBroker for EdgeRouter Lite”

WireGuard wg-quick PostUp的高级玩法

真的很高级。 wg-quick是WireGuard用来启动网络设备的**脚本**。注意了，迄今为止，wg-quick是用bash写的一个脚本，不知道未来会不会变，至少目前shebang是

!#/bin/bash

1	!#/bin/bash

Incoming search terms:WG-QUICKwireguard高级wireguard ipv6wireguard mtuwireguard postupearnecfhonoreu1hillzqqgreatlyzzhgrain51lgarageai8fingerv55excepts9hcomposedfjachosenem5点对多点wireguardbusy64ubirthdaygz9beyondxdearticlerrqLink to this post!